Building American Quality… With A Lifetime Warranty!
Step 3: After cutting housing, install end of housing into GM or
Chrysler trans end fitting. Figure 1 Slide housing nut up
and tighten until housing is locked into fitting. Figure 2
Note: Do Not over tighten nut as it will result in fitting failure.
Step 4: Install inner cable into the housing with the square
end towards the transmission gear. Install inner cable
into gear, making sure it bottoms out in this gear.
Screw trans end fitting on trans and route housing to
speedo with the inner cable installed. At the speedo
head, mark inner cable flush with the end of the
speedo end fitting. Figure 3
Step 5: Remove inner cable. Cut at mark, debur inner cable
and install tip.
Stop! Please read all installation instructions before
beginning installation. Call Lokar with any questions or
uncertainties during your installation.
WARNING: Do not take trans end fitting off of housing.
Slide fitting back onto housing when ready to cut
housing.
CUttING SUGGEStIoN FoR BLACK HoUSING AND
INNER CABLE: For cutting cable and housing, we
suggest using quality diagonal cutters, i.e., Klein
Cutters, Part No. D2000-28 or Grainger’s No. 4A838.
CUttING SUGGEStIoN FoR StAINLESS StEEL
HoUSING AND INNER CABLE: Cutting braided cable
housing is easy. Simply wrap the housing with masking
tape where the cut is to be made, clamp the housing in
a vise and then cut with a fine-tooth hacksaw. Remove
the tape before final assembly. Use the wire cutters
suggested above for cutting the inner cable.
A NotE ABoUt ALUMINUM FIttINGS: Always use an
anti-seize lubricant when tightening threaded fittings.
U-Cut-To-Fit Speedometer Cable Kit Installation
Step 1: Install outer housing to speedometer and route hous-
ing to transmission, making sure to keep away from
exhaust pipes.
Step 2: Hold housing up to transmission to determine length
and mark a cut line. Remove housing from vehicle
and cut housing at the cut line. Figure 1
10924 Murdock Dr. • Knoxville, TN 37932
TOLL FREE
1-877-469-7440 •
(865) 966-2269
• FAX
(865) 671-1999
•
[email protected] • www.lokar.com
U-Cut-To-Fit GM & Chrysler
Speedometer Cable Kit Instructions
Part # SP-1500U, SP-1501HT, SP-1504U, SP-1505HT
U-Cut-To-Fit GM & Chrysler Speedometer Cable Kit
Installation Instructions
Part # SP-1500U, SP-1501HT, SP-1504U, SP-1505HT
Step 6: Place inner cable and tip (A) into crimping die (B).
Figure 4
Step 7: Make sure tip is pushed onto inner cable completely.
Using pliers, hold crimping die onto a solid surface
and strike squarely with a hammer.
Step 8: Remove crimping die by prying apart with a
screwdriver.
Step 9: Before final installation of inner cable into outer
housing, LUBRICATE with light grease. Install in car.
Figure 1
Trans End Fitting
Outer Housing
Outer Housing
Ends Here
Figure 2
Tighten housing nut
only far enough to
lock on housing
Figure 3
Speedo End Fitting
Mark inner cable flush with end
Figure 4
A
B
Inner Cable
© 2007 Lokar, Inc.
Rev. 3/04/09 RPD 07/01/10
®
(1 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels